PIXEL Subscribe FR EN

Bitaxe not connecting to Wi-Fi: the fixes, in order

Most of the time, a Bitaxe that will not join Wi-Fi is not broken: it only sees 2.4 GHz, and your router offers it a 5 GHz-only network, or a single name that mixes the bands. A separate 2.4 GHz network with its own name fixes that case. Here are the six checks in order, then router settings, the on-screen messages, and how to switch networks or reset everything.

Published 23 September 2026, updated 28 October 2026 · by Pixel · 12 min read

Video The topic on video Play the video: Bitaxe in 2026: understanding the open-source Bitcoin miner 6:25
Bitaxe in 2026: understanding the open-source Bitcoin miner Video in French, with subtitles · open on YouTube The video loads from YouTube when you press play.
In short

The Bitaxe only uses 2.4 GHz Wi-Fi: its ESP32-S3 chip cannot see 5 GHz. The usual blocker is a 5 GHz-only network, or bands merged under one name. Give it a separate 2.4 GHz network with a signal better than -70 dBm, then check the password and WPA2 (AxeOS 2.15.4, October 2026).

Contents 9 parts and a FAQ · 12 min read
  1. Which checks, in which order?
  2. What does the on-screen message mean?
  3. How do you split out 2.4 GHz on your router or ISP box?
  4. Smart routers, mesh, repeaters: why does it get stuck?
  5. How do you test with a phone hotspot or the guest network?
  6. How do you change the Wi-Fi on a Bitaxe that is already set up?
  7. How do you reset a Bitaxe?
  8. Connected to Wi-Fi, but nothing reaches the pool?
  9. What if nothing works?

1. Which checks, in which order?

  1. Is the network 2.4 GHz? The Bitaxe cannot see 5 GHz: its chip, the ESP32-S3 A microcontroller worth a few euros, the kind in smart plugs. It can compute SHA-256, but millions of times slower than an ASIC chip: an ESP32 miner has no real chance. The lottery miner trap, only does 2.4 GHz Wi-Fi in 802.11 b, g and n, according to Espressif’s product page. If your router merges the bands under one name and the connection fails, enable a separate 2.4 GHz network (each French ISP’s method is below) and give that name to the Bitaxe. If your router can restrict 2.4 GHz to Wi-Fi 6 (802.11ax) only, keep mixed mode.
  2. Is the password exact? Upper case, lower case and special characters all count. When the connection fails, AxeOS The open-source Bitaxe software, set from a browser: pool, frequency, voltage, fan. Update it brings its own Wi-Fi network back up, named Bitaxe_ followed by four characters, waits five seconds and tries again, with no limit: you can fix it at any time.
  3. Router security. If your Wi-Fi is set to WPA3 only, switch it to mixed WPA2/WPA3 mode: some small devices only connect over WPA2. AxeOS requires at least WPA2 as soon as a password is entered: a network still on WEP or first-generation WPA is rejected. On AxeOS 2.15.0, some mixed-mode networks failed: update (see the table below).
  4. Distance. The Bitaxe antenna is small. Move it next to the router to test: if it connects, a repeater or a better spot will solve it. Once connected, AxeOS shows the signal strength (RSSI): 4 bars above -50 dBm, 3 above -60, 2 above -70, a single bar below that.
  5. Connected but cannot find it? Its IP address is shown on its screen (a short press on the BOOT button cycles the pages), and it appears in your router’s device list under its hostname, bitaxe by default. Since AxeOS 2.15.0, http://bitaxe.local also works if your network handles mDNS. With several Bitaxes on the same network, only one keeps that name: the others get a suffixed name, such as bitaxe-xxxx, so the IP address on the screen remains the safest bet.
  6. Power supply. A weak supply makes the machine reboot in a loop, which looks like a Wi-Fi problem. Use the supply meant for your model: 5 V and 6 A for a Gamma 601, per my Bitaxe Gamma review. A boot loop can also come from overheating: see Miner running hot.

These checks apply to every Bitaxe running AxeOS. NerdQAxe machines run a derived version of the software: their setup network starts with “NerdAxe” (see my NerdQAxe++ Hydro review), and their menus may differ.


2. What does the on-screen message mean?

Until it connects, the Bitaxe shows the network it is trying (the “Wi-Fi:” line), a status message followed by an error number, then the name of its setup network and, since AxeOS 2.11, a QR code to join it. The message tells you where to look:

AxeOS 2.15.4 connection messages, read in its source code (ESP-Miner) on 28 October 2026. The numbers are ESP-IDF Wi-Fi reason codes, from Espressif’s framework.
On-screen message What it means What to do
No access point found (201) No network with that name is visible. Check that it broadcasts on 2.4 GHz, the exact name (case included) and the distance.
Incorrect password entered (15) The key exchange fails: AxeOS reports it as a wrong password. Type it again, then try mixed WPA2/WPA3 mode.
IE differs in 4-way handshake (17) AxeOS 2.15.0 bug with some mixed WPA2/WPA3 networks. Move to 2.15.1 or later.
No access point found with compatible security (210), No access point found in auth mode threshold (211) The network is seen, but its security does not fit. WPA2 or WPA2/WPA3 on the router, empty password if the network is open.
Beacon timeout (200) The router’s signal was lost. Move the machine closer or add a repeater.
IP Acquire Timeout Accepted by the router, but no IP address within 30 seconds. Restart the router, then the Bitaxe.
Config AP connected! A device is connected to the Bitaxe network: the machine pauses its attempts. Leave that network once the settings are saved.

The exact meaning of each code is in the ESP-IDF documentation. The 2.15.0 bug was reported in August 2026 (issue 1904) and fixed in 2.15.1, released on 29 August 2026. To update a machine that no longer connects, first get it onto a simple WPA2 network, a phone hotspot for instance, or go through USB (see below).


3. How do you split out 2.4 GHz on your router or ISP box?

A single name for every band does not necessarily stop the Bitaxe from connecting: it only sees the 2.4 GHz part of it. But when it fails, a 2.4 GHz network with its own name is the safest fix. On most routers, look in the Wi-Fi settings for an option that gives each band its own name. Here is what the four French ISPs document on their official help pages (in French), checked on 28 October 2026. I only repeat their own paths: menus change from one model to the next.

  • Orange (Livebox): splitting is done in the Orange et moi app (Gérer votre wifi, Configurer votre réseau wifi, then Séparer les bandes wifi), on Mon Réseau Local, or in the Livebox interface with the “SSID différent pour 5 GHz” setting. The Livebox then broadcasts two names: give the Bitaxe the 2.4 GHz one. Orange warns that devices left on 2.4 GHz lose Wifi Intelligent, and that TV boxes on Wi-Fi and Orange Wi-Fi repeaters must be paired again. Orange’s page.
  • Free (Freebox): two methods, for every Freebox. In the Freebox Connect app, under Appareils, the + button, “Ajouter un appareil en 2.4 GHz” then “Forcer temporairement le 2.4 GHz” switches the other bands off while the device connects, for 15 minutes at most (Free’s page). For a lasting split, under Réseau, Modifier, then Type de configuration Wi-Fi, choose Séparée and save (Free’s page), or use Freebox OS. Free then suggests going back to the Unique setting: only do so if the Bitaxe uses a name that still exists, or it will lose the network.
  • Bouygues Telecom (Bbox): the Bbox picks the band itself (2.4, 5 or 6 GHz depending on the model) when Wi-Fi is unified, the “Unifier mon Wi-Fi” setting in the app (Gérer ma Box, Accéder à mon interface admin, then Mes réglages Wi-Fi). Its help page does not describe splitting the bands: if the Bitaxe refuses the unified network, ask customer service for the steps on your model.
  • SFR: the SFR Box 10 and 10+ offer a “WiFi compatible” network, meant for older devices or those that struggle with the main private Wi-Fi. That is the one to give the Bitaxe if it refuses the main network (SFR’s page). SFR also advises against changing the private Wi-Fi’s encryption and points to this network for incompatible devices (its page on customising the Wi-Fi). For other SFR boxes, I found no official page on splitting the bands.

4. Smart routers, mesh, repeaters: why does it get stuck?

Recent routers and mesh systems broadcast one name over several bands, sometimes from several access points (Free’s Unique setting, the Bbox’s unified Wi-Fi), and pick each device’s band themselves: that is how Orange describes its Wifi Intelligent, SFR its Smart WiFi and Bouygues Telecom the Bbox.

AxeOS is built for this. Among access points with the same name, it connects to the one with the strongest signal. Since version 2.3 it supports 802.11k and 802.11v, the standards these systems use to move a device from one access point to another (SFR states that its Smart WiFi relies on 802.11k, v and r), and since 2.4, switching access point is no longer treated as a dropout.

When it still gets stuck:

  • Put the machine near an access point that broadcasts 2.4 GHz, and check the signal in AxeOS: a single bar means below -70 dBm.
  • Split out a 2.4 GHz network if your router or mesh allows it, as above.
  • Pair your repeaters again after splitting the bands on a Livebox: Orange asks for it with its Orange Wi-Fi repeaters.
  • If the problem started after an update, check the AxeOS version. In August 2026, investigating the 2.15.0 bug, the developers first asked whether the network was a mesh, in mixed WPA2/WPA3 mode, with protected management frames (PMF) or 802.11r fast transition. The cause was the handling of mixed mode, fixed in 2.15.1.

5. How do you test with a phone hotspot or the guest network?

To find out whether the problem is the Bitaxe or the router, give it a simple network right next to it: your phone’s hotspot.

  1. Turn on the hotspot. On iPhone: Settings, then Personal Hotspot, and also turn on Maximize Compatibility, which Apple suggests when a device cannot connect. On Android: touch and hold Hotspot in the quick settings, then turn on Wi-Fi hotspot (Android Help). If your phone lets you pick the band, choose 2.4 GHz.
  2. Give that network to the Bitaxe through its setup network, with a simple name and password for the test.
  3. Read the result. If it connects and mines, the machine and its Wi-Fi are fine: the cause is on the router side (band, security, distance). If it fails a metre from the phone, look at the on-screen message and the power supply.
  4. Then put your home Wi-Fi back, or the Bitaxe will depend on your phone and its data plan.

The guest network can serve as a test, not as a lasting fix. SFR describes it as a network that lets guests connect to the Internet only, and Free recommends keeping its access level on “Internet uniquement” (each guest key there gets an expiry chosen when it is created). The Bitaxe will mine there, since it only needs the Internet to reach its pool A server that machines connect to. A regular pool shares the earnings, a solo pool does not. Solo or pool?, but you probably will not be able to open AxeOS from a device on the main network, and an expiring guest key will cut it off.


6. How do you change the Wi-Fi on a Bitaxe that is already set up?

Setup network Bitaxe_ plus 4 characters, open
Setup page 192.168.4.1
On your network IP on the screen, or http://bitaxe.local (AxeOS 2.15 and later)
AxeOS page Network
  1. It is still connected (a new password coming, a new router set up next to the old one): open AxeOS, Network page. Enter the name in Wi-Fi SSID (the magnifier lists networks received at -80 dBm or better, hidden networks excluded), the password in Wi-Fi Password, then Save and Restart: the change only applies after the restart.
  2. The old network is gone: nothing to do on the machine. With no connection, it brings its setup network back by itself. Join it with your phone: the setup page opens by itself, otherwise type 192.168.4.1 in the browser. On that network, AxeOS only shows this page. Enter the new network, save, restart, then leave the Bitaxe network. The QR code on the screen saves typing the name, but it is tiny: the developer who added it warns that not every phone can read it.
  3. You want that network without waiting for a dropout: in the AxeOS 2.15.4 code, a two-second long press on the BOOT button, once the machine has started, turns it on or off. Do not hold BOOT while plugging in or pressing RESET: the chip would then start in flashing mode, per Espressif’s documentation.

If AxeOS only shows the Network page, the setup network is on: another long press turns it off, and so does a restart, once the connection is back. Meanwhile AxeOS refuses updates (the “Not allowed in AP mode” message): the method is in Update AxeOS.

SFR’s tip works for any router: when you change routers, give the new one your old network name and key, and your devices, the Bitaxe included, reconnect with no setup.


7. How do you reset a Bitaxe?

For a Wi-Fi problem, a reset is rarely needed: the setup network is enough. The ESP-Miner documentation describes no button combination to erase the settings. The method it gives is to flash a “factory” image built for your model and board version: every setting (Wi-Fi, pool, frequency, voltage) goes back to factory values. Write yours down first.

  1. Open the Bitaxe Web Flasher, the project’s official tool, in Chrome, Edge or Brave: it requires a Chromium-based browser.
  2. Plug the Bitaxe into its usual power supply and connect its USB port to the computer. According to ESP-Miner, some Bitaxe versions cannot connect directly to a computer’s USB-C port: use a USB-A adapter then.
  3. Click Connect, pick the port, then the model, the board version (601 or 602 for a Gamma) and the firmware version.
  4. Leave “Keep configuration” unticked: that is what replaces the configuration with the factory one. Ticked, the tool keeps your settings, which is what you want for a plain reinstall.
  5. Start Flashing and wait for the end without unplugging.
  6. Let the self-test run if it starts, then press RESET once it has passed, as the ESP-Miner documentation says. The Bitaxe_ network comes back: set it up again with Set up a Bitaxe, step by step.

Comfortable with Python? ESP-Miner also provides bitaxetool, a command-line tool that flashes the same factory image.


8. Connected to Wi-Fi, but nothing reaches the pool?

If the screen shows an IP address and AxeOS opens, Wi-Fi is doing its job: the problem is further along.

  • Pool settings: host, port, user, with no stray spaces. The details are in the setup guide.
  • The router: the ESP-Miner documentation names ASUS routers and some TP-Link models that block mining, and suggests turning off AiProtection and the IoT features there.
  • The pool: look up your Bitcoin address on its page. On FindMyBlock, the solo pool I run, each machine shows up under its worker name (solo mining on FindMyBlock). A fallback pool takes over if the main one stops answering.

The rest of the diagnosis, zero hashrate Computing power: the number of attempts per second of a machine or of the whole network. The higher it is, the more tickets you play in each draw., rejected shares An attempt good enough to be counted by the pool. It proves your machine is working, even if it is not enough to find a block., a machine that will not mine: Bitaxe not hashing.


9. What if nothing works?

Note the exact Bitaxe model, the AxeOS version, the exact on-screen message and the signal strength, then ask on Discord: several of us answer there. And if the machine has to stay far from the router, know that the Bitaxe only has Wi-Fi, while some desk miners have an Ethernet port, like the Thor P2 I reviewed.


Frequently asked questions

Does the Bitaxe work on 5 GHz Wi-Fi?

No. Its chip, Espressif’s ESP32-S3, only handles 2.4 GHz Wi-Fi (802.11 b, g and n). It needs a 2.4 GHz network, either separate or sharing one name with 5 GHz.

How do I put a Bitaxe back into Wi-Fi setup mode?

It does so by itself as soon as it cannot find its network: it brings back its Bitaxe_ network followed by four characters, and the setup page is at 192.168.4.1. Once the machine has started, a two-second long press on the BOOT button also turns it on (AxeOS 2.15.4).

How do I find my Bitaxe’s IP address?

It shows on its screen, and your router lists it among connected devices, under the name bitaxe by default. Since AxeOS 2.15.0, http://bitaxe.local also works if your network handles mDNS.

Should I split my router’s Wi-Fi bands for a Bitaxe?

Not necessarily: try the router’s single name first, the Bitaxe will only see its 2.4 GHz part. If it will not connect, split out a 2.4 GHz network with your ISP’s method, and keep that split as long as the Bitaxe uses that name.

Why does my Bitaxe drop off at night?

If the dropout always happens at the same time, check your router’s Wi-Fi schedule: Orange and Bouygues Telecom document scheduled Wi-Fi shutdowns. Otherwise, check the signal and the power supply. The Bitaxe reconnects by itself as soon as the network comes back.


Sources

A question about this guide? Ask it on the Discord, several of us answer there.

Share X WhatsApp Telegram


Other guides

See all 41 guides

@pixel_pow All of this is on video too. Join the channel's 3.4K subscribers.
Subscribe

Back to the ticket

Back of the ticket: legal notice, privacy, terms