PIXEL Subscribe FR EN

Should you turn your Bitcoin miner off at night, or run it 24/7?

It is a question that keeps coming up in the comments and on Discord: can you leave a Bitaxe running 24 hours a day without frying it, or should you let it rest at night? Intuition says a machine that never stops wears out faster, like a car. In electronics it is rather the opposite. Here is why, what actually wears, the settings that let you mine all year without worry, and what switching off at night does to your odds.

Published 4 November 2026, updated 14 November 2026 · by Pixel · 10 min read

Video The topic on video Play the video: Should you turn off your Bitcoin miner at night? (Bitaxe 24/7) 7:17
Should you turn off your Bitcoin miner at night? (Bitaxe 24/7) Video in French, with subtitles · open on YouTube The video loads from YouTube when you press play.
In short

No: switching a miner off every night does not spare it. Each stop takes the chip from about 60 °C down to room temperature, and those cycles fatigue the solder joints. What really wears on a 24/7 miner is the fan, the thermal paste and the power supply. Switching off 8 hours a night also removes a third of your solo draws.

Contents 8 parts and a FAQ · 10 min read
  1. Does turning your miner off at night make it last longer?
  2. What actually wears on a miner that never stops?
  3. What temperatures should you aim for when mining 24/7?
  4. Which power supply for a miner that never stops?
  5. Barrel jack, XT30, XT60: how do you keep a connector from overheating?
  6. How many block chances do you lose by switching off at night?
  7. My checklist for running a miner day and night
  8. So, Team 24/7 or Team switch-off?

1. Does turning your miner off at night make it last longer?

No, and often the opposite. Under the heatsink, the ASIC A chip built for a single task. Bitcoin mining chips can only compute hashes, but extremely fast. chip is soldered to the circuit board by a large number of tiny solder balls. When the miner runs, the chip heats up, say to around 60 °C, and everything expands slightly: the chip’s silicon, the board’s copper and glass fibre, the tin of the solder. As long as the machine stays at a steady temperature, nothing moves: the solder joints are not under strain.

Switch the miner off in the evening and the chip drops towards 20 °C within minutes: everything contracts. In the morning it climbs back to 60 °C and everything expands again. That is a thermal cycle. Because silicon and the circuit board do not expand at exactly the same rate, each cycle pulls a little on the solder joints. Repeated hundreds of times, those small strains end up creating microcracks: this is solder fatigue, a well-known mechanism in electronics.

Its effect should not be overstated: one cycle a day will not ruin a machine in a few weeks. But it gives the chip no rest either. A chip does not need a breather: the ones in our small miners belong to the same family as Bitmain’s Antminer chips (the BM1370 Bitmain's chip from the Antminer S21 Pro, also used in the Bitaxe Gamma and most recent desk miners. in the Bitaxe Gamma also powers the Antminer S21 Pro), built for farms that run for years without stopping.


2. What actually wears on a miner that never stops?

Saying electronics like stability does not mean nothing wears. On a miner running day and night, there are three real consumables to keep an eye on.

1. The fan. It is the only moving mechanical part. Spinning flat out 24 hours a day, its bearings wear: it starts to get noisy, then slows down or seizes. That is why many of us replace the small stock fan with a longer-lasting, quieter one. The official Bitaxe Gamma repository itself recommends a 5 V, four-pin Noctua NF-A4x10, and warns that active cooling is mandatory: the heatsink alone is not enough.

2. Thermal paste. After months of heat, entry-level paste dries out and conducts heat less well. As a result, at the same frequency, the chip runs a few degrees hotter than on day one (I mention 5 to 8 °C in the video). Replacing the paste once a year with a good product resets the clock. The step-by-step method: miner running hot.

3. Power supply and connectors. In a power brick, it is mostly the capacitors that age, and they age faster the hotter they run. A cheap brick delivering close to its full rating all the time runs hot and may fail early. On the connector side, a poor contact creates electrical resistance, so heat right at the contact point: that is what blackens or melts a plug in continuous use.


3. What temperatures should you aim for when mining 24/7?

In AxeOS The open-source Bitaxe software, set from a browser: pool, frequency, voltage, fan. Update it, everyone watches the chip temperature. Also watch the voltage regulator (VR): it is the part that heats up most when you raise the frequency. Here are my targets for a machine running non-stop, next to the limits of the official Bitaxe FAQ and the protection written into the ESP-Miner code:

Bitaxe temperatures in AxeOS: my target for continuous running (video of 3 November 2026), the official FAQ limits (osmu.wiki, read on 4 November 2026) and the point where ESP-Miner 2.15.4 stops mining.
Temperature in AxeOS My target for 24/7 Official FAQ limit ESP-Miner automatic stop
Chip (ASIC Temperature) 55 to 65 °C under 70 °C above 75 °C
Voltage regulator (Voltage Regulator Temperature) under 75 to 80 °C under 90 °C above 105 °C

My target is deliberately more cautious than the FAQ: a machine running all year needs headroom for the days when the room is warmer. In automatic mode, the AxeOS fan actually aims for 60 °C by default, right in that range. Above 75 °C for the chip or 105 °C for the regulator, ESP-Miner stops mining, lets it cool, then restarts with lower settings: details in the overclock guide.

If your temperatures creep up over the weeks with the same settings, it is nearly always dust, the fan or the thermal paste: causes and fixes.


4. Which power supply for a miner that never stops?

The rule I follow: never draw more than 80% of the power supply’s maximum rating continuously. If your miner draws 100 W at the wall, do not buy a 100 W brick; get at least 125 W, and 150 W for peace of mind. A brick with headroom runs cooler, and its capacitors age more slowly. For 24/7 use, pick a quality supply built to deliver continuously.

Here is where a few machines from my reviews stand with the supplied or recommended power supply:

Power supply load in continuous use: the machine’s draw divided by the brick’s maximum rating. Figures from my published reviews, with their source in brackets.
Machine Draw Power supply Load
Bitaxe Gamma 15 to 18 W (rated) 5 V and 6 A, so 30 W (the one in my review) 60%
NerdQX 8T 165 W (from the interface) 250 W, included 66%
NerdQX 8T pushed past 10 TH/s about 215 W (from the interface) 250 W, included 86%
Thor P2 153 W (measured at the wall) 12 V and 20 A, so 240 W, included 64%

At stock settings, these three machines stay under 80%. The NerdQX 8T pushed past 10 TH/s goes above it: it works, but that is where the power supply works hardest. For the Bitaxe Gamma, the official repository asks for a supply delivering more than 4 A (20 W) at 5 V only, often one rated at 25 or 30 W. Watch the Input Voltage line in AxeOS: below 4.8 V, the official FAQ reads it as a sign of an undersized supply.

What those watts cost over a year: Bitcoin miner power consumption.


5. Barrel jack, XT30, XT60: how do you keep a connector from overheating?

A desk miner draws a lot of current for its size: a 5 V Bitaxe Gamma goes beyond 4 A. At those currents, the slightest resistance at a contact turns into heat. In continuous use, it is the half-seated plug that heats, blackens and ends up melting, not the chip.

  • 5.5 × 2.1 mm DC barrel jack (Bitaxe Gamma and most small miners): push it all the way in, with no play. It is the weak point of small miners: the benchmark script shown in the overclock guide even caps power at 40 W because of this plug.
  • XT30 and XT60 (multi-chip machines, such as the Bitaxe Gamma GT on XT30, the Thor P2 and the NerdQX 8T on XT60): these connectors from the RC hobby handle far more current and are keyed, but they too must be pushed all the way home.
  • Touch the plug and cable now and then while the machine runs: lukewarm is normal; too hot to keep a finger on, or a smell of plastic, means switch off and check the contact.

6. How many block chances do you lose by switching off at night?

Beyond the hardware, there is a simple reason to keep running: the odds. In solo mining there is no progress towards a block. Every hash A 64-character code computed from the block. Impossible to predict: you have to try. is an independent draw, and the network draws a new block every 10 minutes on average. Switching your miner off resets no counter, and switching it back on loses nothing from before.

But during 8 hours off, the network finds about 48 blocks without you holding a single ticket. Over a year, switching off every night means giving up a third of your draws. The math with the difficulty How many attempts it takes on average to find a block. It adjusts itself about every two weeks. Difficulty explained as of 14 November 2026, electricity at €0.20 per kWh:

Odds of finding a Bitcoin block solo and yearly electricity cost, running non-stop or off 8 hours a night (network as of 14 November 2026, electricity at €0.20 per kWh).
Machine Running Block odds per year Electricity per year
Bitaxe Gamma (1.2 TH/s, 18 W rated) on 24/7 1 in 15,300 about €32
Bitaxe Gamma (1.2 TH/s, 18 W rated) off 8 hours every night 1 in 23,000 about €21
Thor P2 (10 TH/s, 153 W measured at the wall) on 24/7 1 in 1,840 about €268
Thor P2 (10 TH/s, 153 W measured at the wall) off 8 hours every night 1 in 2,750 about €179

To be fair: switching off at night removes a third of the odds, but also a third of the bill. Per euro of electricity, your odds stay the same. So the real question is not wear, it is how much you are willing to spend, and noise. If your electricity costs much more at certain hours, switching off during those hours can make sense: the math for your tariff. And of course, Murphy’s law loves to land the block right while the miner is unplugged.

Your own numbers, with your machines: the solo mining calculator. To understand solo mining: solo mining with FindMyBlock, my own pool A server that machines connect to. A regular pool shares the earnings, a solo pool does not. Solo or pool?.


7. My checklist for running a miner day and night

The rules I apply to my own machines so they run all year without turning the room into a furnace:

  1. Watch two temperatures in AxeOS: the chip between 55 and 65 °C, the regulator under 75 to 80 °C. If they climb, improve the cooling rather than forcing it.
  2. Size the power supply so it never runs above 80% of its rating continuously, keeping overclocking Pushing the chip's frequency and voltage for more hashrate. It draws and heats noticeably more: on the Thor X1, +50% hashrate for 2.1 times the power. The review in mind if you plan to do it.
  3. Check the connectors: plug pushed all the way in, no play, neither cable nor plug too hot to touch.
  4. Dust it every one to two months, with a blast of dry air into the heatsink fins, machine unplugged, without even opening it.
  5. Replace the thermal paste once a year, or as soon as the temperature rises with the same settings.

If the machine still starts rebooting or losing hashrate Computing power: the number of attempts per second of a machine or of the whole network. The higher it is, the more tickets you play in each draw., the troubleshooting guide goes through the causes one by one.


8. So, Team 24/7 or Team switch-off?

As long as your temperatures are under control, your power supply has headroom and you are not running an extreme overclock that strains the connectors, your miners are built to run 24 hours a day, 7 days a week. Switching them off every evening does not make them last longer, and it costs you a third of your odds.

There are still good reasons to switch off: noise in a bedroom, heat in the middle of summer, or electricity that is very expensive at certain hours. Those are comfort or budget choices, not longevity ones. In winter, on the contrary, the miner’s heat warms the room: heating your home by mining Bitcoin.

What about you: have your machines been running non-stop for months, or do you switch them off at night? Tell me in the comments of the video.


Frequently asked questions

Should I turn off my Bitaxe at night?

Not to protect it: a Bitaxe is built to run continuously, and every stop creates a thermal cycle that fatigues the solder joints. Only switch it off for noise, heat or the cost of electricity.

Can a Bitcoin miner run 24/7?

Yes, ASIC chips are designed to run continuously for years. Keep the chip between 55 and 65 °C, the regulator under 75 to 80 °C, the power supply under 80% load and the connectors fully seated.

What wears out on a miner that runs all the time?

Mainly the fan, the only mechanical part, the thermal paste that dries out over the months, and the power supply, whose capacitors age with heat. Half-seated connectors can also overheat.

How many block chances do you lose by switching your miner off at night?

Switching off 8 hours a night removes a third of your draws: the network finds about 48 blocks during those 8 hours. You also save a third of the electricity, so your odds per euro spent stay the same.

What power supply do I need for a 24/7 miner?

One whose maximum rating is at least 25% above the miner’s draw, to stay under 80% load: at least 125 W for a 100 W miner. For a Bitaxe Gamma, a 5 V brick of 25 to 30 W.


Sources

A question about this guide? Ask it on the Discord, several of us answer there.

Share X WhatsApp Telegram


Other guides

See all 41 guides

@pixel_pow All of this is on video too. Join the channel's 3.4K subscribers.
Subscribe

Back to the ticket

Back of the ticket: legal notice, privacy, terms